292 lines
9.7 KiB
Arduino
292 lines
9.7 KiB
Arduino
|
//gyroscope stuff
|
||
|
|
#include <Adafruit_MPU6050.h>
|
||
|
|
#include <Adafruit_Sensor.h>
|
||
|
|
#include <Wire.h>
|
||
|
|
|
||
|
|
Adafruit_MPU6050 mpu;
|
||
|
|
|
||
|
|
//temporary variable to measure main loops
|
||
|
|
int temp_loops;
|
||
|
|
|
||
|
|
float AccX, AccY, AccZ;
|
||
|
|
float GyroX, GyroY, GyroZ;
|
||
|
|
float accAngleX, accAngleY, gyroAngleX, gyroAngleY, gyroAngleZ;
|
||
|
|
float roll, pitch, yaw;
|
||
|
|
float AccErrorX, AccErrorY, GyroErrorX, GyroErrorY, GyroErrorZ;
|
||
|
|
float elapsedTime, currentTime, previousTime;
|
||
|
|
int gyro_x, gyro_y, gyro_z;
|
||
|
|
long gyro_x_cal, gyro_y_cal, gyro_z_cal;
|
||
|
|
boolean set_gyro_angles;
|
||
|
|
|
||
|
|
long acc_x, acc_y, acc_z, acc_total_vector;
|
||
|
|
float angle_roll_acc, angle_pitch_acc;
|
||
|
|
|
||
|
|
float angle_pitch, angle_roll;
|
||
|
|
int angle_pitch_buffer, angle_roll_buffer;
|
||
|
|
float angle_pitch_output, angle_roll_output;
|
||
|
|
|
||
|
|
long loop_timer;
|
||
|
|
int temp;
|
||
|
|
|
||
|
|
//motor stuff
|
||
|
|
const int MotorPinA = 12;
|
||
|
|
const int MotorSpeedA = 3;
|
||
|
|
const int MotorBrakeA = 9;
|
||
|
|
|
||
|
|
const int MotorPinB = 13;
|
||
|
|
const int MotorSpeedB = 11;
|
||
|
|
const int MotorBrakeB = 8;
|
||
|
|
|
||
|
|
const int CCW = HIGH;
|
||
|
|
const int CW = LOW;
|
||
|
|
|
||
|
|
volatile byte half_revolutionsA;
|
||
|
|
volatile byte half_revolutionsB;
|
||
|
|
unsigned int rpmA;
|
||
|
|
unsigned int rpmB;
|
||
|
|
unsigned long timeoldA;
|
||
|
|
unsigned long timeoldB;
|
||
|
|
|
||
|
|
void setup() {
|
||
|
|
//gyroscope
|
||
|
|
Serial.begin(115200);
|
||
|
|
while (!Serial)
|
||
|
|
delay(10); // will pause Zero, Leonardo, etc until serial console opens
|
||
|
|
|
||
|
|
Serial.println("Adafruit MPU6050 test!");
|
||
|
|
|
||
|
|
// Try to initialize!
|
||
|
|
if (!mpu.begin()) {
|
||
|
|
Serial.println("Failed to find MPU6050 chip");
|
||
|
|
while (1) {
|
||
|
|
delay(10);
|
||
|
|
}
|
||
|
|
}
|
||
|
|
Serial.println("MPU6050 Found!");
|
||
|
|
|
||
|
|
mpu.setAccelerometerRange(MPU6050_RANGE_4_G);
|
||
|
|
Serial.print("Accelerometer range set to: ");
|
||
|
|
switch (mpu.getAccelerometerRange()) {
|
||
|
|
case MPU6050_RANGE_2_G:
|
||
|
|
Serial.println("+-2G");
|
||
|
|
break;
|
||
|
|
case MPU6050_RANGE_4_G:
|
||
|
|
Serial.println("+-4G");
|
||
|
|
break;
|
||
|
|
case MPU6050_RANGE_8_G:
|
||
|
|
Serial.println("+-8G");
|
||
|
|
break;
|
||
|
|
case MPU6050_RANGE_16_G:
|
||
|
|
Serial.println("+-16G");
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
mpu.setGyroRange(MPU6050_RANGE_500_DEG);
|
||
|
|
Serial.print("Gyro range set to: ");
|
||
|
|
switch (mpu.getGyroRange()) {
|
||
|
|
case MPU6050_RANGE_250_DEG:
|
||
|
|
Serial.println("+- 250 deg/s");
|
||
|
|
break;
|
||
|
|
case MPU6050_RANGE_500_DEG:
|
||
|
|
Serial.println("+- 500 deg/s");
|
||
|
|
break;
|
||
|
|
case MPU6050_RANGE_1000_DEG:
|
||
|
|
Serial.println("+- 1000 deg/s");
|
||
|
|
break;
|
||
|
|
case MPU6050_RANGE_2000_DEG:
|
||
|
|
Serial.println("+- 2000 deg/s");
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
|
||
|
|
mpu.setFilterBandwidth(MPU6050_BAND_184_HZ);
|
||
|
|
Serial.print("Filter bandwidth set to: ");
|
||
|
|
switch (mpu.getFilterBandwidth()) {
|
||
|
|
case MPU6050_BAND_260_HZ:
|
||
|
|
Serial.println("260 Hz");
|
||
|
|
break;
|
||
|
|
case MPU6050_BAND_184_HZ:
|
||
|
|
Serial.println("184 Hz");
|
||
|
|
break;
|
||
|
|
case MPU6050_BAND_94_HZ:
|
||
|
|
Serial.println("94 Hz");
|
||
|
|
break;
|
||
|
|
case MPU6050_BAND_44_HZ:
|
||
|
|
Serial.println("44 Hz");
|
||
|
|
break;
|
||
|
|
case MPU6050_BAND_21_HZ:
|
||
|
|
Serial.println("21 Hz");
|
||
|
|
break;
|
||
|
|
case MPU6050_BAND_10_HZ:
|
||
|
|
Serial.println("10 Hz");
|
||
|
|
break;
|
||
|
|
case MPU6050_BAND_5_HZ:
|
||
|
|
Serial.println("5 Hz");
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
|
||
|
|
Serial.println("");
|
||
|
|
delay(100);
|
||
|
|
|
||
|
|
calibrateGyro();
|
||
|
|
|
||
|
|
//motor
|
||
|
|
pinMode(MotorPinA, OUTPUT);
|
||
|
|
pinMode(MotorSpeedA, OUTPUT);
|
||
|
|
pinMode(MotorBrakeA, OUTPUT);
|
||
|
|
|
||
|
|
pinMode(MotorPinB, OUTPUT);
|
||
|
|
pinMode(MotorSpeedB, OUTPUT);
|
||
|
|
pinMode(MotorBrakeB, OUTPUT);
|
||
|
|
|
||
|
|
attachInterrupt(0, magnet_detectA, RISING);
|
||
|
|
//attachInterrupt(1, magnet_detectB, RISING);
|
||
|
|
half_revolutionsA = 0;
|
||
|
|
rpmA = 0;
|
||
|
|
timeoldA = 0;
|
||
|
|
|
||
|
|
half_revolutionsB = 0;
|
||
|
|
rpmB = 0;
|
||
|
|
timeoldB = 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
|
||
|
|
/* Get new sensor events with the readings */
|
||
|
|
sensors_event_t a, g, temp;
|
||
|
|
mpu.getEvent(&a, &g, &temp);
|
||
|
|
|
||
|
|
|
||
|
|
//Subtract the offset values from the raw gyro values
|
||
|
|
gyro_x = g.gyro.x;
|
||
|
|
gyro_y = g.gyro.y;
|
||
|
|
gyro_z = g.gyro.z;
|
||
|
|
|
||
|
|
acc_x = a.acceleration.x;
|
||
|
|
acc_y = a.acceleration.y;
|
||
|
|
acc_z = a.acceleration.z;
|
||
|
|
|
||
|
|
gyro_x -= gyro_x_cal;
|
||
|
|
gyro_y -= gyro_y_cal;
|
||
|
|
gyro_z -= gyro_z_cal;
|
||
|
|
previousTime = currentTime; // Previous time is stored before the actual time read
|
||
|
|
currentTime = millis(); // Current time actual time read
|
||
|
|
elapsedTime = (currentTime - previousTime) / 1000; // Divide by 1000 to get seconds
|
||
|
|
|
||
|
|
//Gyro angle calculations
|
||
|
|
angle_pitch += gyro_x * elapsedTime * 180/PI; //Calculate the traveled pitch angle and add this to the angle_pitch variable, rad/s ---> degrees
|
||
|
|
angle_roll += gyro_y * elapsedTime * 180/PI ; //Calculate the traveled roll angle and add this to the angle_roll variable
|
||
|
|
//0.000001066 = 0.0000611 * (3.142(PI) / 180degr) sin function is in radians
|
||
|
|
angle_pitch += angle_roll * sin(gyro_z * 0.000001066); //If the IMU has yawed transfer the roll angle to the pitch angel
|
||
|
|
angle_roll -= angle_pitch * sin(gyro_z * 0.000001066); //If the IMU has yawed transfer the pitch angle to the roll angel
|
||
|
|
|
||
|
|
//Accelerometer angle calculations
|
||
|
|
acc_total_vector = sqrt((acc_x*acc_x)+(acc_y*acc_y)+(acc_z*acc_z)); //Calculate the total accelerometer vector
|
||
|
|
//57.296 = 1 / (3.142 / 180) The Arduino asin function is in radians
|
||
|
|
angle_pitch_acc = asin((float)acc_y/acc_total_vector)* 57.296; //Calculate the pitch angle
|
||
|
|
angle_roll_acc = asin((float)acc_x/acc_total_vector)* -57.296; //Calculate the roll angle
|
||
|
|
|
||
|
|
angle_pitch_acc -= 0.0; //Accelerometer calibration value for pitch
|
||
|
|
angle_roll_acc -= 0.0; //Accelerometer calibration value for roll
|
||
|
|
|
||
|
|
if(set_gyro_angles){ //If the IMU is already started
|
||
|
|
angle_pitch = angle_pitch * 0.96 + angle_pitch_acc * 0.04; //Correct the drift of the gyro pitch angle with the accelerometer pitch angle
|
||
|
|
angle_roll = angle_roll * 0.96 + angle_roll_acc * 0.04; //Correct the drift of the gyro roll angle with the accelerometer roll angle
|
||
|
|
}
|
||
|
|
else{ //At first start
|
||
|
|
angle_pitch = angle_pitch_acc; //Set the gyro pitch angle equal to the accelerometer pitch angle
|
||
|
|
angle_roll = angle_roll_acc; //Set the gyro roll angle equal to the accelerometer roll angle
|
||
|
|
set_gyro_angles = true; //IMU started flag
|
||
|
|
}
|
||
|
|
|
||
|
|
// complementary filter
|
||
|
|
angle_pitch_output = angle_pitch_output * 0.8 + angle_pitch * 0.2; //Take 90% of the output pitch value and add 10% of the raw pitch value
|
||
|
|
angle_roll_output = angle_roll_output * 0.8 + angle_roll * 0.2; //Take 90% of the output roll value and add 10% of the raw roll value
|
||
|
|
|
||
|
|
if(temp_loops>100){
|
||
|
|
Serial.println("");
|
||
|
|
Serial.print(" pitch Angle = "); Serial.println(angle_pitch_output);
|
||
|
|
Serial.print(" pitch Angle abs = "); Serial.println(abs(int(angle_pitch_output)));
|
||
|
|
Serial.print(" pitch Angle measured = "); Serial.println(angle_pitch);
|
||
|
|
temp_loops = 0;
|
||
|
|
}
|
||
|
|
else {
|
||
|
|
temp_loops++;
|
||
|
|
}
|
||
|
|
|
||
|
|
if(angle_pitch_output!=0 && (abs(angle_pitch_output))<50 ){
|
||
|
|
digitalWrite(MotorBrakeB, LOW);
|
||
|
|
digitalWrite(MotorBrakeA, LOW);
|
||
|
|
if(angle_pitch_output<0){
|
||
|
|
digitalWrite(MotorPinB, CW);
|
||
|
|
digitalWrite(MotorPinA, CCW);
|
||
|
|
}
|
||
|
|
else{
|
||
|
|
digitalWrite(MotorPinB, CCW);
|
||
|
|
digitalWrite(MotorPinA, CW);
|
||
|
|
}
|
||
|
|
if((abs(int(angle_pitch_output))*8 + 30)<250){
|
||
|
|
analogWrite(MotorSpeedB,30 + 8*abs(int(angle_pitch_output))); //Wheel close to connections
|
||
|
|
analogWrite(MotorSpeedA,30 + 8*abs(int(angle_pitch_output))); //First experiment wheel
|
||
|
|
}
|
||
|
|
else{
|
||
|
|
analogWrite(MotorSpeedB,250); //Wheel close to connections
|
||
|
|
analogWrite(MotorSpeedA,250); //First experiment wheel
|
||
|
|
}
|
||
|
|
}
|
||
|
|
else{
|
||
|
|
digitalWrite(MotorBrakeB, HIGH);
|
||
|
|
digitalWrite(MotorBrakeA, HIGH);
|
||
|
|
analogWrite(MotorSpeedB,0);
|
||
|
|
analogWrite(MotorSpeedA,0);
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
void calibrateGyro() {
|
||
|
|
for (int cal_int = 0; cal_int < 1000 ; cal_int ++){ //Read the raw acc and gyro data from the MPU-6050 for 1000 times
|
||
|
|
sensors_event_t a, g, temp;
|
||
|
|
mpu.getEvent(&a, &g, &temp);
|
||
|
|
|
||
|
|
gyro_x = g.gyro.x;
|
||
|
|
gyro_y = g.gyro.y;
|
||
|
|
gyro_z = g.gyro.z;
|
||
|
|
|
||
|
|
gyro_x_cal += g.gyro.x ; //Add the gyro x offset to the gyro_x_cal variable
|
||
|
|
gyro_y_cal += g.gyro.y ; //Add the gyro y offset to the gyro_y_cal variable
|
||
|
|
gyro_z_cal += g.gyro.z ; //Add the gyro z offset to the gyro_z_cal variable
|
||
|
|
|
||
|
|
delay(3); //Delay 3us to have 250Hz for-loop
|
||
|
|
}
|
||
|
|
|
||
|
|
// divide by 1000 to get avarage offset
|
||
|
|
gyro_x_cal /= 1000;
|
||
|
|
gyro_y_cal /= 1000;
|
||
|
|
gyro_z_cal /= 1000;
|
||
|
|
|
||
|
|
loop_timer = micros(); //Reset the loop timer
|
||
|
|
|
||
|
|
if (half_revolutionsA >= 20) {
|
||
|
|
rpmA = 30*1000/(millis() - timeoldA)*half_revolutionsA;
|
||
|
|
timeoldA = millis();
|
||
|
|
half_revolutionsA = 0;
|
||
|
|
Serial.println(rpmA);
|
||
|
|
Serial.print(" pitch Angle = "); Serial.println(angle_pitch_output);
|
||
|
|
}
|
||
|
|
|
||
|
|
if (half_revolutionsB >= 20) {
|
||
|
|
rpmB = 30*1000/(millis() - timeoldB)*half_revolutionsB;
|
||
|
|
timeoldB = millis();
|
||
|
|
half_revolutionsB = 0;
|
||
|
|
Serial.println(rpmB);
|
||
|
|
Serial.print(" pitch Angle = "); Serial.println(angle_pitch_output);
|
||
|
|
}
|
||
|
|
}
|
||
|
|
void magnet_detectA()//This function is called whenever a magnet/interrupt is detected by the arduino
|
||
|
|
{
|
||
|
|
half_revolutionsA++;
|
||
|
|
Serial.println("detect");
|
||
|
|
}
|
||
|
|
void magnet_detectB()//This function is called whenever a magnet/interrupt is detected by the arduino
|
||
|
|
{
|
||
|
|
half_revolutionsB++;
|
||
|
|
//Serial.println("detect");
|
||
|
|
}
|